| Subject | Text |
| Pioneer HTV-2 subwoofer conversion | I have an old Pioneer HTV-2. It is kind of like a Bose 3-2-1. There is a proprietary cable that go |
| I have a 2060u as well, and the info from the original poster helped me figure out how to enter and |
|
|
| Component ID | Ahhhh . . Fast or ultra-fast recovery diode - that's most likely the problem. I didn't think of that |
| IM7 Amplifier Board Repair | Hey everybody!
Anyway, I added a subwoofer output to my Altec Lansing IM7 and also added a potent |
| THE SAMSUNG MODEL YOU MENTION IS NOT LCD PROJECTION, IT USES 3 PROJECTION CRTS, IN THE MENU IS A CO |
| SE110 is an error amplifier IC(in a To220 case) made by sanken &used extensively in chopper sup |
| Alpine TDM 7526E car stereo wiring | Hi there, I have just replaced my car stereo with an Alpine TDM 7526E head unit and matching cd stac |
| [quote:e59dd6ff66="javelinpr"]i have the full schematics with the whole block diagrams, printed circ |
| [quote:93c621a9cb="minnie"]You got it! Sony O.E. or it doesn't work! Unless you sub an RCA HOT to So |
| Thanks for this tip!!!
My PSW2500 Subwoofer did the same problem too, the relay pulsated at high |
| Auto power setting for sub-woofer | How does setting the power switch to AUTO on my Boston Acoustics sub-woofer work? It is powered on a |
| Common failure parts are IC1421=LA7832=JVC # LA7832= sub with LA7833, R1541=1.8 ohm,2W (metal fuseab |
| My friends CSW250 sub has also burnt out at R24. Please email [email protected] if you find the res |
| Sony KV-32S26 | Will NTE sub parts be ok or should I get original??
I did find a site in Canada called Pacific Semi |
| awesome reply! i'll check out all of these things.
apon closer inspection i found a white box(i do |
| I'm using sub, Molex 21020-0251 digikey.com |
| [quote:3747f25abb="matthewy"]Thanks....Vtech, when you say feed external power to it, do you mean pl |
|
|
| Not sure how much you know about the system?
You see, the "SAW541/542" was not just the |
| Great got it thanks, gone ahead and bought another sub board (AA95-00705A) for a direct swap and als |
| Toshiba 3787DB - Very low Base / Woofer output | Getting a very low output on the sub woofer, with the sub and the base turned all the way up you can |
| [quote:e49eaef5fd="vtech"]Should not be difficult to determine as to why your sub/w is not working. |
| I need a complete model #. You need the sub deflection board. Look on tritronicsinc. If you replace |
| Hi, i own the same model.
I have a psu problem that im solving right now.
I found that one of the |
| Btw, there are suitable substitutes available such as :
CNY17-2
4N35
ECG3041
H11A1
ECG3096 |
| Description:
POWER SUPPLY (NLA - SEE NOTE)
SPECIAL NOTE:
ORDER SUB PART BASED ON S/N |
| Thank god for this post, the reds and greens were too strong on my 2060u and this helped me fix it c |
| I have a kef 2000 sub, all op transistors went short along with the -15 regulator.
The relay had go |
| JAW 541 | I have been folowing this post regarding the SAW 541 sub/amp. I am curious if anyone found a way to |
| Proel SMT15SA | Hallo!
Please Schema of Amplifier for this Active Sub! Thanks! |
| yes the sub should be wired to the remote wire it should be blue and white.
Hope this helps let m |